How to troubleshoot a solar photovoltaic (PV) system

We expect smooth power generation from a solar photovoltaic (PV) system while sun shining. When the sun is out but the system doesn't generate electricity as per required capacity, then we consider the system as problematic. Solar photovoltaic (PV) system occasionally requires troubleshooting as like as other energy systems. The key to your success depends on the strategy you choose for identifying the trouble source. Typically, three problems occur in solar photovoltaic (PV) system. They are-an array problem, inverter problem, or load problem. Concentrating on common troubleshooting problems and solutions can ensure that your system is taking the advantage of summer's sunny days.


Components of a solar photovoltaic (PV) system

Cell, module and array: A typical photovoltaic (PV) cell produces a small electrical output ranges from 0.5W to 2W approximately. As these devices are electrical, we can boost overall output level by wiring them in series and parallel strings. Wiring PV cells in this method is called a module. Some manufacturers now manufacture “power modules,” which can generate 190W or more power. Under full sun shine conditions, a typical 190W module which is connected to a load might generate the voltage and current of approximately 27V and 7A respectively. When modules are wired in series and parallel strings, then it is called an “array.” The output of an array is designed in such a way that the output of an array can meet almost any electrical requirement of small or large scale system.

Combiner box: Desired voltage and current can be gained by wiring modules into an electrical string. All strings are combined into one electrical output in the combiner box which is then fed to the inverter.

Inverter: Inverter converts the DC output into AC as per requirement of any photovoltaic (PV) system. Electric utility grid connected inverters generate AC which is identical to the power generated by the electric utility. These inverters sense the waveform characteristics and generated voltage of the electric utility and generate the same type of AC.

How to troubleshoot the problem of an array

The input voltage and current level of the inverter's from the array need to be checked and recorded. If the array is not generating required DC electricity, check all switches, fuses, and circuit breakers. Blown fuses should be replaced and the breakers and switches need to be reset. A specious surge might have passed through, blowing or tripping the protective devices. Loose or dirty connections and broken wires in the inverter should be checked. All connections should be clean and make them tighten. All damaged wires should be replaced. Check the array visually for obvious damage to the panels and wiring.

There are fuses for each module or sub-array string in many combiner boxes. While troubleshooting, all these fuses should be removed and the current reading and open-circuit voltage should be recorded for each circuit string. Low output voltage indicates that some panels in the series string are disconnected or defected which requires replacement. Defective bypass or blocking diodes in the modules might need to be replaced. Wrong wiring connecting the modules in the string to the combiner box, junction box or the inverter may cause low voltage. Undersized wire may cause this problem. This problem should be rectified by upgrading the wire size for the current level.

During overcast or cloudy conditions, a damaged panel or defective bypass diode can produce low output current. One or more parallel connections between modules in the string might be loose, broken, or dirty — or some parallel connections in the module might be loose, broken, or dirty. Replace a damaged module or one with internal parallel connection problems. Defective diodes should be replaced. All connections need to be tightened and clean. Shades on the array decreases output current significantly. So, in order to obtain full current output from the string, it is required to remove the source of shades from array.

Dirty modules decrease the output current. In order to restore the output current of array, these modules need to be washed. After washing, the output current should be checked again.

How to troubleshoot the problem of an inverter

First of all, operating DC input voltage and current level of the inverter should be checked by a volt meter and DC ammeter respectively. After then, these data should be recorded. On the AC side, check the inverter’s output voltage and current level. A blown fuse, broken wires or a tripped breaker can cause the insufficient output power from the inverter.

Some inverters have LED displays as indicators. It is necessary to check whether these LEDs are blinking properly or not. Properly blinking LEDs should indicate the actual condition of the inverter.

True-rms reading type volt meter can be used to measure the voltage and current to measure. After measuring, the kilowatt output should be recorded. You should record the total kilowatt hours generated since it first started up which is displayed by the inverter. You can compare the PV system’s production since the last inspection by using the recorded data.

AC load side of the inverter should be measured, because load on the inverter might have too high demand of a current. In this scenario, inverter should be upgraded or loads should be reduced.

Before starting the inverter again, any ground faults should be checked and repaired after shutting down the power. Inverter can sense the voltage and frequency of the electric utility. Typically, it generates AC electricity at the same voltage and frequency. The AC output current output of the inverter fluctuates with the level of solar input on the array. If internal disconnects sense that the electric utility voltage is high or low, then it will shut down the inverter. If this problem remains, then you should contact the concerned authority of electric utility to rectify the problem. Inverter problems could also be caused by a problem on the array side of the inverter, which trips one of the internal disconnects.


How to troubleshoot a load problem

All load switches should be checked first. It should be checked whether they are turned off or placed in the wrong position. You should check and ensure that the load is plugged in. Next, the fuses and circuit breakers should be checked. If there are tripped breakers or blown fuses, the cause should be located and the faulty component should be replaced or fixed. If there are no tripped breakers or blown fuses and the load is a motor, then there might be an open circuit in the motor or an internal thermal breaker might be tripped. In this scenario, you need to plug in another load and observe its operation.

Any loose connections and broken wires should be checked. All bad wiring should be replaced. After shutting down the power, any ground faults should be checked and repaired. Fuses need to be replaced and the switches should be reset. If they blow or trip again, there might have short circuit problem, which must be located and repaired.

If the load does not operate properly, the system voltage should be checked at the load’s connection point. Too small or too long wire feeding the circuit may cause the low voltage which needs to be upgraded to reduce the voltage drop. The load might also be large enough for the wire size in the circuit. In this scenario, the size of wire need to be upgraded or the load on the circuit should be reduced.

Prasun Barua

Prasun Barua is an Engineer (Electrical & Electronic) and Member of the European Energy Centre (EEC). His first published book Green Planet is all about green technologies and science. His other published books are Solar PV System Design and Technology, Electricity from Renewable Energy, Tech Know Solar PV System, C Coding Practice, AI and Robotics Overview, Robotics and Artificial Intelligence, Know How Solar PV System, Know The Product, Solar PV Technology Overview, Home Appliances Overview, Tech Know Solar PV System, C Programming Practice, etc. These books are available at Google Books, Google Play, Amazon and other platforms.

24 Comments

  1. Thank you for sharing this blog, I am facing this PV problem But dont know how to get rid of it, This blog really helped me a lot. Thank you again for sharing, I appreciate your work done. Solar power kits South Africa

    ReplyDelete
  2. bring revenue and savings to rural and agricultural enterprises while providing the environmental benefits that accompanies renewable energy. Bristol Cost of Solar Panels

    ReplyDelete
  3. I am in fact grateful to the owner of this web site who has shared this great paragraph at here.
    Solar Thermal System

    ReplyDelete
  4. I recently came across your blog and have been reading along. I thought I would leave my first comment. I don't know what to say except that I have enjoyed reading. Nice blog. I will keep visiting this blog very often.
    solar

    ReplyDelete
  5. Finally I have found something which helped me. Appreciate it!
    solar photovoltaic systems

    ReplyDelete
  6. Thank you for sharing valuable information. Nice post. I enjoyed reading this post.
    Solar Electricity Installation
    Solar Las Vegas

    ReplyDelete
  7. Thanks for sharing this article here about the photovoltaic system. I am impressed by the details that you have shared in this post and It reveals how nicely you understand this subject. Keep sharing these types of articles here. Photovoltaic Panels Ireland

    ReplyDelete
    Replies
    1. Thanks Joseph for reading the post and commenting. You're welcome.

      Delete
  8. Thanks for sharing nice blog, i have learn many more.
    ........................................
    Solar Water Pump

    ReplyDelete
  9. This is a much needed guide for heat pump replacement part. This article serves well in its way.
    Heating and Cooling Mississauga

    ReplyDelete
  10. It is just a balanced (a unbiased) comparison between tank v/s tank less water heater. Amazing points have been written.

    https://www.furnaceac.com

    ReplyDelete
  11. Really thanks for sharing this useful post about photovoltaic (PV) system. Keep posting informative content regarding solar system .

    ReplyDelete
Post a Comment
Previous Post Next Post